Silicon condensors

Circuit Break Podcast #12

Silicon Condensors

Related Topics
Magical Semiconductors of Pixies

We’re joined by Alexander Vartanov, an electrical engineering student with a knack for hands-on projects.

Wizard Trust Falls for PCB Footprints

Parker’s transition from Eagle to KiCad, facing challenges with library management and device layer integration. Also, the new MacroFab Quote Wizard.

Tracing a Path for PCB Design Automation with Sergiy Nesterenko

Sergiy Nestorenko, founder of Quilter and former SpaceX engineer, discusses revolutionizing PCB design automation.

Other Resources

Circuit Break Podcast
Blog
eBooks & Guides
Webinars
Videos
Case Studies
Tour MacroFab's ITAR-Compliant Facility

April 22, 2016, Episode #12

Stephen builds a custom old school tube microphone for Josh Moore and Parker gets a CU40045-UW1J display working.
  • Stephen built a power supply for an old school tube microphone for Josh. Josh does the recordings for the Podcast. See Figure 1 for the schematic.
  • Microphone is a Sony C37 tube condenser microphone.
  • Parker has been working on an article for the blog about designing and building simple test fixtures for low to medium volume production runs. See Figure 2.
  • Parker has also been working on code to run a large VFD display. Part number is CU40045-UW1J. This is for Parker’s fan controller for his Jeep. See Figure 3.
  • Blunty released a really cool video of a tour of the Nvidia Silicon Failure Analysis Lab. The equipment is pricey! They can pinpoint the exact transistor that fails on the die.
  • Microchip released the PICDEM Lab II. Parker used a PICDEM Lab I for developing the MacroWatch REV 1. Stephen was watching the video about it and the recommended video was about Dave Jones ragging on the PICKIT 3.
  • Desktop Siege Cannon that uses flash paper to make a fireball. Should we design an ECE version that uses electrolytic capacitors charged in reverse polarity to cause them to rocket out the barrel?
  • Big Clive took apart a USB soldering iron that actually works! Parker thinks with USB 3.1’s higher power rating of 100W a serious soldering iron could be designed.
Figure 1: Schematic for the power supply Stephen made for Josh’s microphone. Drawn by Stephen.

Figure 1: Schematic for the power supply Stephen made for Josh’s microphone. Drawn by Stephen.

Figure 2: Simple Fixture Parker made for testing and programming a development board.

Figure 2: Simple Fixture Parker made for testing and programming a development board.

About the Hosts

Parker Dillmann
  Parker Dillmann

Parker is an Electrical Engineer with backgrounds in Embedded System Design and Digital Signal Processing. He got his start in 2005 by hacking Nintendo consoles into portable gaming units. The following year he designed and produced an Atari 2600 video mod to allow the Atari to display a crisp, RF fuzz free picture on newer TVs. Over a thousand Atari video mods where produced by Parker from 2006 to 2011 and the mod is still made by other enthusiasts in the Atari community.

In 2006, Parker enrolled at The University of Texas at Austin as a Petroleum Engineer. After realizing electronics was his passion he switched majors in 2007 to Electrical and Computer Engineering. Following his previous background in making the Atari 2600 video mod, Parker decided to take more board layout classes and circuit design classes. Other areas of study include robotics, microcontroller theory and design, FPGA development with VHDL and Verilog, and image and signal processing with DSPs. In 2010, Parker won a Ti sponsored Launchpad programming and design contest that was held by the IEEE CS chapter at the University. Parker graduated with a BS in Electrical and Computer Engineering in the Spring of 2012.

In the Summer of 2012, Parker was hired on as an Electrical Engineer at Dynamic Perception to design and prototype new electronic products. Here, Parker learned about full product development cycles and honed his board layout skills. Seeing the difficulties in managing operations and FCC/CE compliance testing, Parker thought there had to be a better way for small electronic companies to get their product out in customer's hands.

Parker also runs the blog, longhornengineer.com, where he posts his personal projects, technical guides, and appnotes about board layout design and components.

Stephen Kraig
  Stephen Kraig

Stephen Kraig is a component engineer working in the aerospace industry. He has applied his electrical engineering knowledge in a variety of contexts previously, including oil and gas, contract manufacturing, audio electronic repair, and synthesizer design. A graduate of Texas A&M, Stephen has lived his adult life in the Houston, TX, and Denver, CO, areas.

Stephen has never said no to a project. From building guitar amps (starting when he was 17) to designing and building his own CNC table to fine-tuning the mineral composition of the water he uses to brew beer, he thrives on testing, experimentation, and problem-solving. Tune into the podcast to learn more about the wacky stuff Stephen gets up to.

Special thanks to whixr over at Tymkrs for the intro and outro!